Injection molding machine price is only the entry ticket; over the machine’s life, electricity and other running costs usually add up to far more, and a hybrid servo system can cut up to 40–60% of the energy a hydraulic machine uses, without replacing the machine.
Your monthly power bill spirals up, and you wonder why a machine you bought years ago still feels so expensive. Find your answer here.
What Is the Injection Molding Machine Price, and What Does It Really Cover?
Let’s start with the number everyone asks about first. The injection molding machine price is what you pay to get the machine into your factory. That is the plastic injection molding machine price on the quotation, plus freight, installation, and sometimes a mould and auxiliaries.
Here is what moves the price:
- Tonnage (clamping force): a bigger machine costs more.
- New or used: a reconditioned Japanese machine usually costs less upfront than a new one of the same size.
- Brand and age: well-known brands hold value better.
- Drive type: hydraulic, hybrid or all-electric.
- Condition and hours run: for used machines, this matters a lot.
Why Is My Injection Molding Machine Electricity Bill So High?
Because a standard hydraulic machine keeps a big pump motor running whether or not it needs full power at that moment.
Think about one moulding cycle: the machine closes the mould, injects, holds pressure, cools the part, opens and ejects. During the cooling stage and the holding pressure stage, the machine needs very little oil flow. But a conventional fixed displacement pump keeps spinning at full speed. The extra energy turns into heat, which warms up the hydraulic oil and then forces your cooler to work harder, adding even more electricity consumption.
You can work it out yourself with one simple formula:
Yearly electricity cost = average power (kW) × running hours × tariff per unit (₹/kWh)
Here is an illustrative example. These are assumed numbers, not a quote, so replace them with your own meter readings:
Item | Assumed value |
Average power draw of the machine | 20 kW |
Running hours per year (20 hrs × 300 days) | 6,000 hours |
Electricity tariff | ₹8 per kWh |
Yearly electricity cost | ₹9.6 lakh |
If energy use falls by 40% | ₹3.84 lakh saved per year |
If energy use falls by 60% | ₹5.76 lakh saved per year |
Injection Molding Machine Price vs Running Cost: Which One Matters More for Tota l Cost of Ownership?
Choice | Upfront cost | Power bill | Best for |
Buy a new all-electric machine | Highest | Lowest | New plants, precision parts |
Keep your hydraulic machine as it is | None | Highest | Machines that run only a few hours |
Keep it and add a hybrid servo system | Moderate | Much lower | Existing machines that run long hours |
What Is a Hybrid Servo System, and How Does It Save Power?
A hybrid servo system swaps the always-on pump motor for a servo-controlled drive. In simple words, the motor speeds up when the machine needs oil flow and slows down when it doesn’t.
Listed specifications for hybrid servo systems show 40% less energy use than variable displacement pump systems and 60% less than traditional fixed displacement pump systems.
- Energy savings: 40% less than variable displacement pump systems and 60% less than traditional fixed displacement pump systems.
- Cooler oil: oil temperature is reduced by 5–10°C, oil usage by 50–60%, and the oil tank can be 50% smaller. A smaller cooler, or none at all, may be enough.
- Better repeatability: the system keeps product-to-product difference under 0.09%.
- Long holding pressure: it keeps the mould halves closed for longer, which helps with thick plastic products.
- Fast response: the advanced series with a permanent magnet servo motor reaches a response time of 50 ms.
How Can I Reduce Injection Molding Machine Power Consumption Without Buying a New Machine?
Start with the free and cheap fixes, then move to the retrofit:
- Measure first. Put a meter on the machine and learn your real kWh per hour.
- Switch off idle machines. Standby machines still draw power.
- Check barrel heaters and insulation. Heater bands that lose heat make the machine work harder.
- Optimise cycle time. Shorter, tighter cycles mean fewer kWh per part.
- Keep oil and filters clean. Dirty oil makes the pump work harder.
- Match machine size to the job. A 300-ton machine running a 100-ton job wastes power.
- Add a hybrid servo system. It addresses the biggest cause of waste: the pump running at full speed when it doesn’t need to.
Where Can I Buy Machines and Hybrid Servo Systems in India?
At Advance Plastic Machinery. The company has supplied plastic machinery from Noida since 1993 and is listed as a trader, importer, exporter and supplier. It stocks 170+ injection moulding machines, from 7 T to 2000 T, from Japanese brands such as Mitsubishi, Toshiba, JSW, Sumitomo, Niigata and Nissei.
It also offers auxiliaries such as hopper dryers, crushers, auto loaders and mould temperature controllers, plus the Hybrid Servo System for energy saving. You can browse used machines, new machines, the Hybrid Servo System and the finance options.
Conclusion: Is the Lowest Injection Molding Machine Price Really the Cheapest?
A low injection molding machine price looks great on the quotation, but the running cost is what you live with every month. Looking at the full picture, combining purchase, power, and upkeep, shows where the money really goes.
Ready to see what you could save? Share your machine tonnage, running hours and monthly power bill with the team at Advance Plastic Machinery for a retrofit assessment, or send a quick enquiry on WhatsApp at +91 88822 20909.
Frequently Asked Questions
What is the price of an injection molding machine in India?
Tonnage, brand and age determine the injection molding machine price in India. Reconditioned Ask for a written quote that lists what is included.
How much electricity does an injection molding machine use?
It depends on tonnage, cycle time, material and pump type. You can measure your own machine’s kWh over a full shift, then multiply by hours and tariff.
What is the running cost of an injection molding machine?
Electricity, oil, cooling, maintenance and labour are needed to keep the machine producing. They add up to the running cost of an injection molding machine
Is a hybrid servo system worth it on an old hydraulic machine?
If the machine runs long hours and is mechanically sound, a hybrid servo system is worth it.
Can I retrofit a hydraulic injection molding machine with a servo system?
In many cases, yes. However, it depends on the machine and controller, so ask for a site assessment first.



